Top 10 common forklift mishaps ， forklift operation ought to take note of these matters ！.

Do not ignore the forklift at work. If the operation is bad, there will certainly be significant accidents in minutes, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the car when it surrendered and was crushed.
Forklift operation must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no obstacles that impede the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe prior to starting.
3. When the forklift begins with a load, the motorist ought to initially confirm that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole needs to be tilted in reverse. .
2. Do not raise the fork too expensive when driving. When getting in and leaving the job site or while driving, take care that there will be no challenges overhead. When the lots is traveling, the fork needs to not be elevated too high, which will influence the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the tons need to not block the chauffeur's sight. In special circumstances, when the thing influences the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when getting in the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for workers to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will certainly never operate with ailments or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, security warning signs need to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be kept in mind that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward a little when the load is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork impend. Prior to leaving the forklift, you need to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Eliminate the key. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are full and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the cars and truck;.
2. When you come across someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of " cost-free switching";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the incline is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile needs to be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and progress, if they encounter big or hefty products and most Stand-on Electric Pallet Stacker likely to the chauffeur's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork procedure is not allowed.
2. It is not permitted to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to make use of stopping force to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the obstacle should be within 20 Electric Forklift Truck for Warehouse meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844